METAL SOLUTIONS

EOS Titanium TiCP Grade 2

Material Data Sheet

EOS Titanium TiCP Grade 2

The parts built with EOS Titanium TiCP grade 2 powder have chemical composition corresponding to ASTM F67. The parts have good strength-to-weight ratio, corrosion resistance and ductility. Parts built with EOS Titanium TiCP grade 2 powder can be machined, shot-peened and polished in as-built and heat treated states. Due to the layer-wise building method, the parts have a certain anisotropy.

MAIN CHARACTERISTICS

  • Good strength-to-weight ratio
  • Good corrosion resistance & ductility

Download Process Data Sheet (PDF)

TYPICAL APPLICATIONS

  • Parts for medical and other industries

The EOS Quality Triangle

EOS uses an approach that is unique in the AM industry, taking each of the three central technical elements of the production process into account: the system, the material and the process. The data resulting from each combination is assigned a Technology Readiness Level (TRL) which makes the expected performance and production capability of the solution transparent.

EOS incorporates these TRLs into the following two categories:
 
  • Premium products (TRL 7-9): offer highly validated data, proven capability and reproducible part properties. 
  • Core products (TRL 3 and 5): enable early customer access to newest technology still under development and are therefore less mature with less data.

All of the data stated in this material data sheet is produced according to EOS Quality Management System and international standards
EOS 3D Printing Solutions Quality Triangle

POWDER PROPERTIES

EOS Titanium TiCP Grade 2 powder corresponds to ASTM F67

Powder Chemical Composition (wt.-%)

Element Min. Max.
N 0.0 0.03
C 0.0 0.08
H 0.0 0.015
Fe 0.0 0.3
O 0.0 0.25
Ti Balance

Powder Particle Size

GENERIC PARTICLE SIZE DISTRIBUTION 38 - 45 μm

HEAT TREATMENT

Description

Heat treatment procedure

Steps

Heat treatment in 700 °C (± 10 °C) for 2 h (± 0.5 h) under argon.

Process Data Sheet

EOS Titamium TiCP for EOS M 290 | 30 µm

EOS M 290 - 30 µm

System Setup EOS M 290
EOS Material set TiCP 30µm FlexLine
Software Requirements

EOSPRINT 1.3 or newer

EOSYSTEM 2.3 or newer
Recoater Blade HSS (High Speed Steel)
Inert gas Argon
Sieve 63 µm
Additional Information
Layer Thickness 30 µm
Volume Rate 5.0 mm³/s

Microstructure of the Produced Parts

Density Thickness Result Number of Samples

Mechanical Properties

Mechanical Properties As Manufactured

EN ISO 6892-1 Room Temperature Yield Strength [MPa] Tensile Strength [MPa] Elongation at Break A [%] Reduction of Area Z [%] Number of Samples
Vertical 560 660 22 30 - -
Horizontal 560 660 22 30 - -

The numbers are average values and are determined from samples with horizontal and vertical orientation.

The numbers are average values and are determined from samples with horizontal and vertical orientation.

Mechanical Properties Heat Treated

EN ISO 6892-1 Room Temperature Yield Strength [MPa] Tensile Strength [MPa] Elongation at Break A [%] Reduction of Area Z [%] Number of Samples
Vertical 445 570 26 30 - -
Horizontal 445 570 26 30 - -

Heat treatment in 700 °C (± 10 °C) for 2 h (± 0.5 h) under argon. 
The numbers are average values and are determined from samples with horizontal and vertical orientation.

The numbers are average values and are determined from samples with horizontal and vertical orientation.

Hardness

EN ISO 6507 Heat Treated
Value 195
Unit HV5

Surface roughness after shot peening

Post-processed
Value

Ra < 10 µm; Rz < 55 µm
Generate und open PDF